5.8Ghz Adjustable 25/200/500mW Switchable 48CH Betaflight/Cleanflight OSD Setting Video Transmission Custom Power Settings FPV VTX

Price: $19.99


Qty. 
+-
Free Shipping
  
Features: 
Adjustable 4 modes:25mW/200mW/500mW/OFF 
Betaflight/Cleanflight OSD configuring parameter
Clean powerup and channel switching without interference to others
Smaller current(12V power supply : 220mA/500mW)

Specifications:
Frequency: 5.8G 48CH
Transmitting Power:25mW/200mW/500mW/OFF(Pitmode)
Power supply:DC7-26V(6S) 
Current(12v):90mA(25mW)/130mA(200mW)/220mA(500mW) 
Weight: 4.4g
Standard size: 29.9*21.7*4.85mm
 

User manual:
1.LED indication
    The red LED indicates the state of working mode or the item when setting the VTX(flashing 1 time means selecting the channels, flashing 2 times means selecting the bands, flashing 3 times means selecting the power levels).
    The blue LED indicates the state of Pitmode or the value of item when setting the VTX( e.g. when selecting the channels, 3 times of flashing means channel 3. When selecting the bands, 3 times of flashing means band C.As for the item of power levels,3 times of flashing means at the  power level of 500mW)
    The green LED flashing indicates that the VTX overheat protection is working, the power level will go down

2.Working mode indication
    After powering up, the red & blue LEDs will signal the following three items of VTX in turn: channel, band and power level(the flashing times of the red and blue LEDs indicate the item and the value respectively). After that, the LEDs indicate the working modes.
    Normal: The red & blue LED are on. 
    Pitmode:The red LED is on and blue LED is off. 

3. Setting
    Press and hold the button until the red LED flash 1 time which means the item of channel selecting, then press the button can select the channels(blue LED flashing times corresponds to the channel 1-8). 
    Press and hold the button again,the red LED will flash 2 times which means the item of band selecting, then press the button can select the band(blue LED flashing times corresponds to the band A-F).
    Press and hold the button again,the red LED will flash 3 times which means the item of power level selecting, then press the button can select the power(blue LED flashing times corresponds to the power level).
    Finally, press and hold the button, save and exit the setting of VTX(This step is essential for setting).
    Press the button twice will toggle the ON/OFF of Pitmode.
For Betaflight/Cleanflight OSD setting of channel,band,power and Pitmode ,please referring to ‘Betaflight OSD setting of EWRF Transmitter’for details.  

4.Custom power settings 
    Press the button and turn on the power for 10 seconds.,the transmitter will enter the advanced mode. Blue light off, increase the fourth gear power file (custom power).The fourth and fifth setting, add the two settings of values for the custom power file.There are 100 values (the fourth file represents ten digits,the fifth file represents digits .) These 100 values represent the percentage of 600mw to 25mw.

Note:
1.Make sure that there is enough space for airflow when installing the module   on the drone in case the overheating protection starts to reduce the power   even to shut down at the worst.
2.Please install the antenna before powering up for a longer use life.
3.The maximum current of output DC 5V is 500mA. 
           
Package Include:
Adjustable e708TM3 PRO 48CH transmitter *1


  • Model: e708TM3 pro
  • Units in Stock100

This product was added to our catalog on Wednesday 11 July, 2018.